Is standard shredding killing your efficiency? If you process long PVC pipes, conduit, or profiles, learn why a standard shredder might be the wrong choice, and how a Horizontal Crusher eliminates manual cutting.
If you process long PVC pipes, conduit, or window/door profiles, your biggest cost isn’t electricity—it’s handling. Manual cutting, unstable feeding, and frequent material bridging in the hopper quietly destroy your profit margins.
Many buyers assume a heavy-duty shredder is the default first step for recycling. But for full-length PVC pipes, that assumption often creates the exact problems you are trying to solve.
This guide compares the two technologies and explains why a Horizontal PVC Pipe Crusher is usually the superior ROI choice.
The Core Problem: Why Shredders Struggle with Long Pipes
A standard shredder is designed for bulk. It excels at chewing up heavy purge lumps, bales, or short, thick scraps. However, when you feed a 6-meter long PVC pipe into a standard top-fed shredder hopper, physics works against you:
The Hidden Costs of Shredders for Pipes
- Bridging: The pipe often “rests” across the opening rather than falling into the rotor.
- The “Whip” Effect: The rotor grabs one end of the pipe, causing the other end to whip around violently.
- Low Efficiency: The machine runs empty half the time while operators struggle to force the pipe in.
Result: You are forced to manually cut pipes. This defeats the purpose of automation.
Comparison: Standard Shredder vs. Horizontal Crusher
Which machine fits your production line? Here is the breakdown.
| Functie | Standaard Shredder | Horizontal Pipe Crusher (Recommended) |
|---|---|---|
| Het beste voor | Lumps, bales, short blocks | Long pipes (3m, 6m), profiles |
| Invoermethode | Vertical (Top-fed) Hopper | Horizontal (Side-fed) Trough |
| Pre-cutting? | YES (Must cut long pipes) | NO (Feeds whole lengths) |
| Uitvoergrootte | Large Chunks (40-100mm) | Regrind/Flakes (8-12mm) |
| Process Steps | 2 Steps (Shredder + Crusher) | 1 Step (Direct to Regrind) |
The Verdict: If your primary scrap is long material, the Horizontal PVC Pipe Crusher is the correct tool. It aligns the pipe with the rotor, allowing gravity or nip-rollers to feed it smoothly.
How the Horizontal Crusher Workflow Works
Instead of forcing operators to stand over a dangerous hopper, the horizontal design changes the geometry of recycling:
- Laden: The operator (or a conveyor) places the full-length pipe into a long horizontal trough.
- Auto-Feeding: The machine automatically pulls the pipe into the cutting chamber at a controlled speed.
- One-Step Granulation: The pipe is immediately reduced to 8-12mm flakes, ready for re-extrusion or washing.
There is no “shredding” phase. You go from Waste Pipe → Final Regrind in one pass.
What About Window Profiles? (Steel & Gaskets)
A common question we get: “My uPVC window profiles have rubber gaskets and steel reinforcements. Can I crush them?”
Yes, but the workflow changes slightly. While the Horizontal Crusher handles the length perfectly, the contamination requires downstream separation (Magnetic separation for steel, Density separation for rubber).
Practical Line Layouts
Depending on your material, here are the two most common plant configurations:
Layout A: Long-Pipe Focused (Recommended)
Het beste voor: Clean pipes, profiles, immediate regrind use.
- Lowest footprint & energy cost.
- Eliminates manual cutting stations.
Layout B: De-bulking First
Het beste voor: Mixed bales, ultra-heavy lumps, or dirty scrap.
Opmerking: Higher maintenance and power cost. Only use if material is mixed/baled.
Veel Gestelde Vragen
Technically yes, but it is inefficient. Pipes often bridge across the hopper opening, and the “whipping” motion creates safety risks. Shredders work best for pipes that are already cut short.
Use a Horizontal Crusher. It has a side-feeding trough designed to accept 3-meter or 6-meter pipes directly, eliminating the need for pre-cutting labor.
Use a shredder if your material is mixed (bales, lumps, and pipes together) or if the pipes are ultra-heavy wall thickness that might overload a direct crusher.
Get an Accurate Quote Today
To help us recommend the right machine size and calculate your ROI, please include these details in your inquiry:
Copy & Paste Checklist:
- Materiaal: (e.g., Rigid PVC pipe, Window profiles, Mixed)
- Size: Max Diameter & Wall Thickness (mm)
- Length: (e.g., 6 meters, 3 meters)
- Besmetting: (Any steel, rubber gaskets, or clean?)
- Target Output: (e.g., 500 kg/h)
- Voeding: (Voltage / Hz / Phase)
